This tutorial describes the unpacking and assembly process for Sawyer and any purchased accessories
- 1 Required Hardware
- 2 Choose Appropriate Workspace
- 3 Unpack Contents
- 4 Pedestal Setup
- 5 Mounting Sawyer
- 6 Controller Setup
- 7 Power On
- 8 Video
- Pallet jack
- Flat-head screwdriver (pedestal only)
- 24mm Socket wrench (pedestal only)
- 6mm Hex key
- Electric Parallel Gripper Kit (EPG)
- Vacuum Gripper Kit (VG)
- Mobile pedestal
- Mounting plate
Choose Appropriate Workspace
It is important to choose an appropriate location for Sawyer to reside where the arms can fully stretch without risk of collision.
Please see Sawyers reachable workspace documentation: Sawyer's workspace guidelines for help choosing a location.
See the Setting Up Sawyer video at the bottom of this page for more information and video instructions. Refer also to the Sawyer Setup Guide located in the accessories box.
- Using a pallet jack, move the robot, pedestal and all accessories to an area close to the workspace. Ensure that there is adequate room to open all boxes and the crate and unpack the contents.
- Open the accessories box in order to obtain the Setup Guide.
- Open the robot and controller boxes and set them aside in preparation for mounting the robot and controller.
- Locate the power, communication, and display cables in the accessories box and ensure they are accessible. See the section below for a list of contents included in the accessories box.
- Unpack the pedestal first if one was purchased with the robot. See the next section for the complete pedestal unpacking and setup instructions.
Note: Please confirm all parts ordered are include in the shipment, and all packaging is intact.
Note: The pedestal base weighs 169 lbs., and Sawyer weighs 42 lbs.. Follow proper lifting guidelines and restrictions for these weights.
Accessories Box Contents
More information coming soon!
The Robot Positioning System (In Intera) uses landmarks placed in the workspace. A landmark is a design or mark placed in the field of view of an imaging system to be used as a point of reference. It is similar in some ways to a registration mark used in printing to keep the different images aligned. Rethink Robotics currently supplies landmarks on anodized aluminum with an adhesive backing. These landmarks are placed on the surface of modules in the work area.
Note:Landmark numbers 1-4 are included with the purchase of a robot and 5-20 can be purchased as an additional accessory.
(Optional) Applicable when using the standard Sawyer pedestal.
Refer to the Sawyer Setup Guide located in the accessories box and the video at the bottom of this page for more information.
Note: Please contact Rethink Robotics Support for a PDF copy of the Sawyer Setup Guide.
- 24mm Socket Wrench
- Flathead Screwdriver
- Using a flathead screwdriver, pry up each of the metal tabs on top edge of the pedestal crate and remove the cover from the crate.
- Using the same technique, remove one of the longer sides of the pedestal crate.
- Raise the leveling feet until they clear the supports, about 3 cm (1 in).
- Roll out the pedestal base. Pedestal weighs 77 kg (169 lbs.)
- Lock wheels at he back of the pedestal.
- Open the largest of the three cardboard boxes in the pedestal crate and remove the 2 threaded rods.
- Remove the column from the box and place the column on the base while aligning the notch.
- Open the second largest of the three cardboard boxes and remove the handlebar.
- Place the handlebar on top of the column with the flat side away from the notch in the column and base.
- Insert the threaded robs into the two large holes in the handlebar while ensuring the washer remains in place.
- Tighten the rods using the 24mm socket wrench.
- Carefully lift the robot arm out of box 1. Avoid lifting Sawyer by the head. Arm weighs 19 kg (42 lbs).
- At the base of the arm are 7 screw holes and 1 dowel hole. Place the arm on the pedestal, aligning the dowel pin hole first.
- Hold the arm in place and insert the screws into the holes at the base of the arm.
- Tighten the 7 screws using a 6mm hex key.
Please see the Alternate Mounting page for more information.
Notes: Power Requirements: 100-240 VAC, 47-63 Hz, 4A MAX Pneumatic Line Requirement: 60-90 PSI Air Must be Filtered and Oil-Free
- Remove the controller from box 2 and place upside down while keeping the foam on the top of the controller for protection. Controller weighs 17kg (38 lbs).
- Obtain the controller and power cables from the accessories box.
- If mounting to the standard pedestal, feed the controller cable and display cable through the back of the controller stand.
- Plug the cables into the controller and ensure they are secure.
- Plug the power cord into the controller and ensure that the cable is secure and latched. Determine which direction the power cord will be fed in order to be routed to the nearest outlet. Feed the power cable through one of the controller stands if necessary.
- If mounting to the standard pedestal, set the controller upright on the back of the pedestal with the door facing away from the pedestal column. Using a 5mm hex key, insert and tighten the 4 provided mounting screws.
- Connect and secure the controller and display cables to the robot. If using a standard pedestal, remove the cable cover from the column, tuck in the cables, and replace the cover to keep the cables in place.
Congratulations! You have now set up your Sawyer Robot. Power on the robot by pressing the power button on Sawyer's controller. Sawyer is fully booted when the green condition light appears on Sawyer's head and the Sawyer SDK Screen shows on the Robot Screen. At this point Sawyer will be homed and enabled.